Frank Marine Rod Holder - Stainless Steel Flush Mount Straight Subtotal: $24.90
Shop
Showing 841–870 of 3715 results
-
Pumps and Plumbing
Flojet RV Pump 2.9GPM 12V
Flojet RV Pump 2.9GPM 12VÂ
- Flow Rate (11 LPM / 2.9 GPM)
- 50PSI Pressure Switch
- Self-Priming to 2.5 metres
- Soft Noise Absorbing Mounts
- 4 x plug-in hose port fi ttings included
- Built-in Bypass valve : Less Pulsation
- Reduces need for accumulator tank
- Corrosion Resistant Materials
- Can run dry for short periods without damage
- Meets ISO 8846 (Ignition protection)
- Thermal overload protection
- 12 volt
- Amp draw 4.4 amp @10PSI : 7.5Amp @ 50PSI
SKU: FJ0100 -
Lighting, Navigation Lights
Floodlight – Deck
Floodlight – Deck
Halogen floodlight, 12 volt, 55 watt. White ABS housing with glass lens. Stainless steel mount hardware adjusts both horizontally and vertically.
BLA CODELENS MMOVERALL HEIGHT MMDEPTH MMMOUNT BOLT MM123057 
120 110 45 8 Spare Parts
124192 Replacement bulb
SKU: 123057 -
Lighting, Navigation Lights
Floodlight – LED Waterproof Deck
Floodlight – LED Waterproof Deck
LED floodlight with 12 extra bright diodes operating at a range between 9 to 36 volts with a low 0.4 to 1.5 amperage draw. Specially designed lens helps spread light beam and is set within a fully waterproof aluminium housing. Includes stainless steel mount adjustable both horizontally and vertically.
BLA CODEOVERALL HEIGH MMWIDTH MMDEPTH MMMOUNT BOLT MM123072 
120 110 45 8 SKU: 123072 -
Electrical, Switches
Flow-Rite MA-103 Livewell ProTimer
Flow-Rite MA-103 Livewell ProTimer
Flow-Rite’s Livewell Pro Timer is a high-quality digital timer designed specifically for use in livewell systems. This compact and easy-to-use timer allows you to control the frequency and duration of the water circulation in your livewell, ensuring that your bait or catch stays healthy and alive for longer periods of time. The Livewell Pro Timer is the perfect solution for any angler looking to maximize the performance of their livewell system. The timer can be programmed to run in continuous mode, or set to run for preset intervals of 1, 2, 3, or 4 minutes, with a maximum run time of 12 hours. The Livewell Pro Timer is compatible with all Flow-Rite livewell systems and can be easily installed in just a few minutes.
ProTimer automatically turns your pump on and off for desired circulation and aeration. Set the ProTimer to the desired interval and concentrate on fishing. ProTimer conserves battery life, is easy to install and operate. It can be connected to an exisiting switch in your boat.
ProTimer Plus+ comes with all the same features plus a master control switch to control on, off, or timed livewell operations.
Dimensions
Pro-timer:
Faceplate (WxH) 1-3/4″ x 2-1/4″
Mounting Depth (from dial to back electronics) 2-5/16″Installation & operation instructions
SKU: RWB10069 -
Electrical, Switches
Flow-Rite MA-104 Livewell ProTimer – plus
Flow-Rite MA-104 Livewell ProTimer +, Faceplate (WxH) 3 5/8″ x 2 1/4″
Flow-Rite’s Livewell Pro Timer is a high-quality digital timer designed specifically for use in livewell systems. This compact and easy-to-use timer allows you to control the frequency and duration of the water circulation in your livewell, ensuring that your bait or catch stays healthy and alive for longer periods of time. The Livewell Pro Timer is the perfect solution for any angler looking to maximize the performance of their livewell system. The timer can be programmed to run in continuous mode, or set to run for preset intervals of 1, 2, 3, or 4 minutes, with a maximum run time of 12 hours. The Livewell Pro Timer is compatible with all Flow-Rite livewell systems and can be easily installed in just a few minutes.
ProTimer automatically turns your pump on and off for desired circulation and aeration. Set the ProTimer to the desired interval and concentrate on fishing. ProTimer conserves battery life, is easy to install and operate. It can be connected to an exisiting switch in your boat.
ProTimer Plus+ comes with all the same features plus a master control switch to control on, off, or timed livewell operations.
Dimensions
Faceplate (WxH) 3-5/8″ x 2-1/4″
Mounting Depth (from dial to back electronics) 2-5/16″Installation & operation instructions
SKU: RWB10070 -
Boating Accessories, Bungs and Scuppers
Flow-Rite remote drain bung with 10″ cable
Flow-Rite remote drain bung with 10″ cable
The SeaLok Remote Drain Plug from Flow-Rite is an innovative solution for water drainage in boats. This product features a reliable and easy-to-use design, with a cable that runs from the plug to a convenient location on the boat’s surface for quick access. The cable can be extended or retracted as needed, allowing for customized positioning to fit different boat configurations.Made from durable materials, the SeaLok Remote Drain Plug is resistant to corrosion and wear, ensuring a long-lasting performance. It features a simple installation process that requires no drilling or modification of the boat, making it an ideal option for those who want to avoid making permanent changes to their vessel.The SeaLok Remote Drain Plug is compatible with most boats, and its compact size allows it to fit in tight spaces. Its unique design provides a watertight seal that prevents water from leaking into the boat, ensuring a dry and comfortable ride. This product is an essential tool for any boat owner, providing a reliable and convenient way to drain water from the vessel.With today’s high performance hull designs, jack plates and larger outboards, putting a drain plug in or taking one out can be a very unpleasant task. The SeaLok™ Remote Drain Plug makes that job as simple as turning a switch.
- No more lying on a wet boat ramp to put in or take out your drain plug
- Never worry about forgetting your drain plug again!
- Easily open or close your drain plug from your console
- Easy to install on most fiberglass or aluminum hull with a 1″ mounting hole
- Fresh or salt water use
Installation and maintenance tips:
-Remote Drain Plug requires a 1″ diameter mounting hole
-Transom thickness should be 3/4″ or less
-A silicone lubricant is recommended during install, but not required
-We recommend monthly maintenance to the drain plug o-ring area including; wiping it clean, re-lubricating the o-ring with silicone lubricant, and checking for debrisSKU: RWB10099 -
Boating Accessories, Bungs and Scuppers
Flow-Rite remote drain bung with 6″ cable
Flow-Rite remote drain bung with 6″ cable
The SeaLok Remote Drain Plug from Flow-Rite is an innovative solution for water drainage in boats. This product features a reliable and easy-to-use design, with a cable that runs from the plug to a convenient location on the boat’s surface for quick access. The cable can be extended or retracted as needed, allowing for customized positioning to fit different boat configurations.Made from durable materials, the SeaLok Remote Drain Plug is resistant to corrosion and wear, ensuring a long-lasting performance. It features a simple installation process that requires no drilling or modification of the boat, making it an ideal option for those who want to avoid making permanent changes to their vessel.The SeaLok Remote Drain Plug is compatible with most boats, and its compact size allows it to fit in tight spaces. Its unique design provides a watertight seal that prevents water from leaking into the boat, ensuring a dry and comfortable ride. This product is an essential tool for any boat owner, providing a reliable and convenient way to drain water from the vessel.With today’s high performance hull designs, jack plates and larger outboards, putting a drain plug in or taking one out can be a very unpleasant task. The SeaLok™ Remote Drain Plug makes that job as simple as turning a switch.
- No more lying on a wet boat ramp to put in or take out your drain plug
- Never worry about forgetting your drain plug again!
- Easily open or close your drain plug from your console
- Easy to install on most fiberglass or aluminum hull with a 1″ mounting hole
- Fresh or salt water use
Installation and maintenance tips:
-Remote Drain Plug requires a 1″ diameter mounting hole
-Transom thickness should be 3/4″ or less
-A silicone lubricant is recommended during install, but not required
-We recommend monthly maintenance to the drain plug o-ring area including; wiping it clean, re-lubricating the o-ring with silicone lubricant, and checking for debrisSKU: RWB10098 -
Boating Accessories, Hinges
Flush Dual Pivot Hingen (29725)
Flush Dual Pivot Hingen (29725)
• 304G Press stainless steel.
• 6x5mm counter sunk mounting holes per hinge.
• Electro Polished HD Flush Mount Stamped Strap Hinge.Features:
Part No:29725
Description:Double Pin Hinge
Length(mm):70
Width(mm):41
Thickness(mm):2
No Mount Holes:6
Mount Holes CS(mm):5
Length Split(mm):35/35SKU: 29725 -
Boating Accessories
Flush Hatch Cover Pull (29793)
Flush Hatch Cover Pull (29793)
• Flush Mounting.
• Suits hatches or engine covers up to 45mm thick.
• Marine grade stainless steel.
• Pin Length 60mm.Features:
Part No.: 29793
Description: Flush Hatch Cover Pull
Ring Diameter (mm): 32SKU: 29793 -
12V Accessories, Electrical
Fold Down Bracket (119568)
Fold Down Bracket (119568)
An easy to install mount bracket to suit LCD or LED TVs. Folding mechanism supports up to 8kg and when mounted under cabinets simply folds through 110° and out of view when not in use. Features integrated swivel mechanism which allows viewing at any angle. Standard VESA mount pattern to suit 50 x 50mm, 75 x 75mm and 100 x 100mm.
Features:
BLA Code: 119568
SKU: 119568 -
Lighting
Folding LED Anchor Lights (709642)
Folding LED Anchor Lights (709642)
• Suitable for boats up to 12 metres long.
• Polycarbonate housing with alloy shaft.
• Wing nut for quick release folding base.
• Internationally approved USCG COLREG 2NM A-16 up to 12 meter vessels.Features:
Part No.: 709642
LED Colour: Cool White
Length (mm): 300
Diameter (mm): 55
Volts: 12
Amps: 0.1
Watts: 1SKU: 709642 -
Boating Accessories, Rod Holders
Frank Marine 3 Way Rod Holder
Frank Marine 3 Way Rod HolderÂ
The Frank Marine stainless steel 3 way portside / starboard rod rack will tie in with your other stainless elements. Built tough from high grade materials for those big catches Frank Marine offers a range of stainless steel accessories for the boat.
- 316 Stainless steel
- Portside mount rod hold or Starboard mount rod hold
- Vertical rotation 180 degree
- Tube diameter 32mm
SKU: FM-99080P, FM-99080S -
Boating Accessories, Rod Holders
Frank Marine Adjustable 25mm Rail Mount Tube Rod Holder
Frank Marine Adjustable 25mm Rail Mount Tube Rod HolderÂ
Heavy duty cast rod holder bolts easily around 20-25mm O/D tube. Can be swivelled to best suit any desired rod angle.
A heavy duty 316 grade stainless steel rod holder and mount that can be adjusted to rotate through 360 degrees in both the horizontal and vertical axis.
The heavy duty cast holder is designed to accept and securely hold most common rods but also allows the rod to be quickly removed when fish strike. Each holder is mounted on a cast stainless steel base which is designed to be clamped around hand rails or rod racks manufactured from 32mm diameter tube.
The rod holder has the ability to be rotated horizontally by simply loosening the top screw. When the desired position is reached match the corresponding teeth and re-tighten for a positive lock. For vertical adjustment simply loosen the clamp screw and rotate around the mounting tube to the vertical angle required.
SKU: BBB-FM99138 -
Boating Accessories, Rod Holders
Frank Marine Adjustable 3 Way Rod Holder
Frank Marine Adjustable 3 Way Rod HolderÂ
The Frank Marine stainless steel adjustable 3 way portside / starboard rod racks are durable and will tie in with your other stainless elements.
This 3 way rod holder is an adjustable rod holder that can be adjusted 360 degrees horizontally and 180 degrees vertically. Frank Marine offers a range of stainless steel accessories for the boat to suit your needs
- 316 Stainless steel
- Port mount rod holder or starboard mount rod holder
- Horizontal rotation 360 degrees
- Vertical rotation 180 degrees
- Tube diameter 32mm
- 3 way adjustable
SKU: FM-99111P, FM-99111S -
Boating Accessories, Rod Holders
Frank Marine Double Wire 25mm/22mm/32mm Stainless Rail Mount Rod Holder
Boating Accessories, Rod HoldersFrank Marine Double Wire 25mm/22mm/32mm Stainless Rail Mount Rod Holder
Frank Marine Double Wire 22mm/25mm/32mm Stainless Rail Mount Rod HolderÂ
Wire rod holder bolts easily around 22mm/25mm/32mm O/D tube. Can be swiveled to best suit any desired rod angle.
A heavy duty 316 grade stainless steel rod holder and mount that can be adjusted to rotate through 360 degrees in both the horizontal and vertical axis.
The bent holder is designed to accept and securely hold most common rods and allows the rod to be quickly removed when fish strike. Each holder is mounted on a cast stainless steel base which is designed to be clamped around hand rails or rod racks manufactured from 22mm/25mm/32mm diameter tubes.
The rod holder has the ability to be rotated horizontally by simply loosening the top screw. When the desired position is reached match the corresponding teeth and re-tighten for a positive lock. For vertical adjustment simply loosen the clamp screw and rotate around the mounting tube to the vertical angle required.
SKU: BBB-FM99270, BBB-FM99117, BBB-FM99136 -
-
12V Accessories, Electrical, Pumps and Plumbing, Water Pumps
Freshwater Tap Kit – Shurflo Electric faucet + TMC Inline Pump
12V Accessories, Electrical, Pumps and Plumbing, Water PumpsFreshwater Tap Kit – Shurflo Electric faucet + TMC Inline Pump
Freshwater Tap Kit – Shurflo Electric faucet + TMC Inline Pump
• Designed to be a secondary pump in a large system to keep pressure even throughout the system.
• To be used with fresh water and salt water.
• Designed for confined spaces.
• Capacity: 280GPH (1060LPH).
• 12.7mm Hose Diameter.
• 360 Degree Rotation in 3 directions: Rotating spout allows a variety of uses.
• Faucet built with ABS plastic to withstand the real world.
• Easy Installation: Complete with mounting hardware. Only 1 hole necessary for mounting.
• Sliding ceramic plate valve: Two ceramic disk plates that slide on each other. Ultra strong ceramics insure reliability and long life, as well as water flow from a trickle to a steady stream.Kit includes:
• 1 x 232145 – Shurflo Electric faucet – 12V.
• 1 x 23183 – Inline Pump – 12V.SKU: SAW-239316 -
Lighting, Navigation Lights
FriLight Dimmers
FriLight Dimmers
Precise lighting control. Suitable for use with either 12 volt or 24 volt lights to 100 watt. Short circuit protection. Not for use with fluoro lighting. A brief press of the up or down button will start an automatic fade to full light or off. Constant depressing of the up or down button enables manual control of light intensity to any desired level.
BLA CODETRIM COLOUR122406 
White 122408 
Chrome SKU: 122406, 122408 -
Lighting, Navigation Lights
FriLight Interior Lights – LED Nova
FriLight Interior Lights – LED Nova
Semi recessed interior light with 10 energy efficient white LEDs. Smooth finish moulded plastic housing. Frosted polycarbonate lens. No visible fastenings. Dual voltage, 12 volt and 24 volt. 2 watt. Available with or without switch.
BLA CODE NO SWITCHBLA CODE SWITCHTRIM COLOUR122318 
122322 White 122320 
122324 Chrome SKU: 122318, 122320
