Garmin Foot Pedal Power Cable
Connect your compatible Force™ trolling motor foot pedal to a 12-V, 24-V or 36-V power source with this replacement cable, which features a 2-pin, threaded power connector and bare end wires.
Connect your compatible Force™ trolling motor foot pedal to a 12-V, 24-V or 36-V power source with this replacement cable, which features a 2-pin, threaded power connector and bare end wires.
Length | 5m, 15m |
---|
Get on fish faster, and stay on the water with the most powerful, most efficient trolling motor available1 — and it’s quiet, too.
Force is more efficient at 24 V than the competition’s 36 V system. No lie.
Wirelessly connect to your Garmin chartplotter, and open up a world of possibilities.
It comes with sonar built in, too? That’s just too good to be true.
All the control of a cable-steered pedal without the cable.
Just point the handheld remote where you want to go, and Force will take you there.
The GT54UHD-TM transducer provides image details so clear and precise, you can actually see fish hanging just off branches of submerged trees, brush and rocks. You can see size differences between bigger and smaller fish and even see individual fish swimming in bait balls. You get the highest resolution ClearVü and SideVü scanning sonar images available plus amazingly clear high wide CHIRP traditional sonar1 — all in one transducer.
Ultra High-Definition scanning sonar provides extended range and depth performance. It shows you incredibly detailed images of fish and structure up to 200’ below your boat with 800 kHz ClearVü, while two SideVü sonar frequency settings (455/1200 kHz) provide options for extended range of up to 500’. It’s easy to install with included transom and trolling motor mounts so you can start fishing faster.
¹For use with GPSMAP® 8400xsv/8600xsv chartplotter/sonar combos
Garmin Stainless Steel Transducer Spray Shield [Garmin Part Number: 010-01055-00]
The Garmin spray shield is designed to reduce excess water spray from transducers when the vessel is running at high speeds. Can be retro fitted to a wide range of common Garmin transom mounted transducers. The plate is simply fitted between the plastic transducer housing and the transom mount bracket. Supplied complete with stainless steel mount fixtures and washers.
COMPATABLE UNITS & TRANSDUCERS:
* echoMAP™ 45dv
* echoMAP™ 55dv
* echoMAP™ 75dv
* echoMAP™ 75sv
* echoMAP™ 95sv
* echoMAP™ CHIRP 45dv
* echoMAP™ CHIRP 55dv
* echoMAP™ CHIRP 75dv
* echoMAP™ CHIRP 75sv
* echoMAP™ CHIRP 95sv
* Garmin GT20-TM – Transom Mount DownVü 500 W (CHIRP 455/800 kHz) Traditional 500 W (77/200 kHz) Transducer with Temp (8-pin)
* Garmin GT21-TM – Transom Mount DownVü 500 W (CHIRP 260/455 kHz) Traditional 600 W (50/200 kHz) Transducer with Temp (8-pin)
* Garmin GT30-TM – Transom Mount DownVü/SideVü 500 W (CHIRP 455/800 kHz) Scanning Transducer with Temp (12-pin)
* Garmin GT40-TM – Transom Mount DownVü/SideVü 500 W (CHIRP 455/800 kHz) Traditional 500 W (77/200 kHz) Transducer with Temp (12-pin)
* Garmin GT41-TM – Transom Mount DownVü/SideVü 500 W (CHIRP 260/455 kHz) Traditional 600 W (50/200 kHz) Transducer with Temp (12-pin)
* Garmin GT50M-TM – Transom Mount DownVü/SideVü 500 W (CHIRP 455/800 kHz) Traditional 300 W (Mid-band CHIRP 80-160 kHz) Transducer with Temp (12-pin)
* Garmin GT51M-TM – Transom Mount DownVü/SideVü 500 W (CHIRP 260/455 kHz) Traditional 600 W (Mid-band CHIRP 80-160 kHz) Transducer with Temp (12-Pin)
*Specifications from suppliers’ information.
Garmin Marine Heading Sensor for Radar [Garmin Part Number: 010-11417-00] – RRP $1200
When interfacing this 3-axis compass heading sensor to our marine lineup of MFDs and radars, mariners can expect unparalleled radar overlay performance and accuracy along with excellent MARPA capabilities.
This heading sensor (based on Airmar H2183) uses a rate gyro, so it can maintain an exceptional 2 degree heading accuracy under heavy dynamic conditions, with up to 30 degrees of pitch and roll. In addition, it supports either NMEA 0183 or NMEA 2000® data output to fit any installation.
Installation is a snap thanks to the heading sensor’s innovative design, allowing it to mount to any angled bulkhead. Mariners can expect this heading sensor to provide trouble-free service in the harshest conditions and will learn to appreciate its reliability and excellent performance.
* Note: NMEA 0183 and NMEA 2000 cables sold separately (to connect to a NMEA 2000 Network a dedicated NMEA 2000 Marine Heading Sensor Cable is required Garmin Part Number: 010-11419-00 – optional, please see related products).
THIS IS SUITABLE FOR CURRENT MODEL GARMIN GMR 18 xHD RADOME & GMR 24 xHD RADOME.
FEATURES:
* Better than 1 degree static heading accuracy
* Industry leading 2 degree dynamic accuracy up to 30 degree pitch and roll
* Three-axis solid-state compass provides accurate heading data
* Three-axis accelerometer improves heading, pitch and roll in static conditions
* Three-axis rate gyro improves heading, pitch and roll in dynamic conditions
* Temperature compensated across the entire operating range to ensure optimum accuracy
* Easy installation to any angled bulkhead
* Auto-calibration feature
SPECIFICATIONS:
* Dimensions (HxLxD): 2″ (5.08 cm) x 4.4″ (11.18 cm) x 4.5″ (11.43 cm)
* Default heading output: 10 Hz for both NMEA 0183 and NMEA 2000 (NMEA 2000 can be output up to 20 Hz)
* Waterproof housing: IPX6
* Operating voltage: 9 VDC to 16 VDC
WHAT’S IN THE BOX:
* Garmin Marine Heading Sensor
* Documentation
WARRANTY:
We are an authorised Australian Garmin retailer, as such Full Australian Manufacturers Warranty is applicable for this item. Please note if a Garmin unit is purchased overseas or from a non-authorised Garmin retailer you may not receive warranty coverage in Australia.
*Specifications from suppliers’ information.